Bucking FLAT Gen2 AEG/HpA - Prometheus [Psionic Upgrades]

There PSI ONIC- UPGRADES proposes a BUCKING, completely made and designed in Italy FLAT. 

In fact, there is no classic internal hump that protrudes inside the INNER BARREL  to give the BACKSPIN to the BB.

The PSI - BUCKING FLAT is designed and calibrated, thanks to its hardness and thickness, to work in symbiosis with the PSI - PATCH and in general with any system R-HOP and to center the BB, before it is pushed towards the PSI -PACTH.

In fact it is equipped with a small inner ring (narrowing) that allows the correct centering of the BB when it is confiscated inside the HOP-UP CHAMBER .

Fundamental when using a system R-HOP is that the BB is perfectly centered before it can receive rotation from PATCH. In this sense it is also possible to use others BUCKING on the market, however, the risk is a drop in overall performance due to the lack of a self-centering system on the lip of the BUCKING. 

The dimensions and shapes of the parts of which it is made up PSI - BUCKING FLAT, in addition to the innovative material, they are designed to guarantee perfect air tightness. 

The sealing lip is in fact designed to obtain total compatibility with NOOZLE (nozzle nozzles) on the market without air leaks and power variations to the chronograph.

Use exclusively NOZZLE (nozzle) flared to avoid permanent deformation of the inlet lip of the BUCKING which could widen and no longer block i BB in entrance. 

Using NOZZLE (nozzles) not flared could occur inconsistencies in the shot and in the correct HOP-UP stamped on BB.

The non-silicone material from which it is made PSI - BUCKING FLAT guarantees excellent elasticity and great resistance to wear.

It can be used in all climatic conditions.

In each package two types of PSI - BUCKING FLAT ASG:

- One PSI - BUCKING FLAT ASG hardness 70 Shore A.

- One PSI - BUCKING FLAT ASG hardness 60 Shore A.

Use the BUCKING suitable for your configuration of INNER BARREL  . 

There INNER BARREL moreover it must be free from play and vibrations inside the OUTER BARREL, in this sense, use Teflon tape so that the  INNER BARREL can join the OUTER as much as possible BARREL, without compromising its correct sliding.

Don't leave the NOZZLE  fully advanced, in contact with the rubber (CLOSED-SEAL), when the replica is not in use, as occurs for example when the spring release is activated in the ICS .

You may need to use some Teflon tape to shim the BUCKING before inserting it into the HOP-UP CHAMBER .

Shim only if there are inconsistencies in the shot due to the excessive presence of empty space between the BUCKING and the HOP-UP CHAMBER .

Shim only the final part of the BUCKING, where the PSI PATCH. 

There PSI ONIC- UPGRADES recommend using your own PSI - BUCKING FLAT exclusively in combination with an R-Hop patch and not as Flat bucking in direct contact with the BBs. 

Clean the PSI - BUCKING FLAT during routine maintenance by removing dirt residues with a cloth.

Don't bring it PSI - BUCKING FLAT in contact with oils, solvents, aggressive sprays and lubricants ( WD-40, VASELLINA etc.),

If necessary, use only silicone / Teflon grease / oil.

To keep its performance unaltered and at its best, use utmost attention and caution in assembly and extraction.

The PSI - BUCKING FLAT it can have an amber or black color depending on availability.

Like all products of PSI ONIC, lo  PSI - BUCKING FLAT it is handmade and scrupulously checked before being placed on the market.

Owns the brand " CE"to guarantee its safe use and disposal in accordance with the law.

----------------------------------------------------------------------------------------------

Exchange / Return:

Psionic-Upgrades - Return / exchange of the product will only be accepted if it has not been handled / damaged.